Stretch Wrapper Pre-Stretch Settings: Ratio, Force-to-Load and Film Savings

Stretch Wrapper Pre-Stretch Settings: Ratio, Force-to-Load and Film Savings

Meta description: Stretch wrapper pre-stretch settings control film yield, containment force and cost per pallet. Learn how pre-stretch ratios, carriage rollers and force-to-load work.

Stretch wrapper pre-stretch settings determine how far a roll of machine stretch film is elongated before it is applied to the pallet. A correct setting works the film close to its engineered limit, reduces film consumption per pallet and keeps containment force steady, while a wrong setting leads to film breaks, loose loads and rewrapping.

Table of Contents

What Are Stretch Wrapper Pre-Stretch Settings?

Pre-stretch settings are the machine parameters that control how much the film web is elongated between the film carriage rollers and the moment it reaches the load. On most pallet wrappers the variables that matter are the pre-stretch ratio, the carriage speed relative to turntable or arm speed, and the film force delivered to the load.

The economics are simple. When film exits the carriage already stretched — commonly to 150 to 250 percent of its original length on machine-grade films — you buy fewer meters per pallet. Stretched film also tries to recover, and that recovery is what tightens the load. A wrapper that applies unstretched film wastes film and often leaves the top layers loose.

For buyers, the settings also define machine cost. A carriage with powered, adjustable pre-stretch costs more than a simple brake carriage, but it typically pays back through film savings on high-volume lines. Requirements may vary by application, machine type and applicable standard.

How Pre-Stretch Works: Carriage, Rollers and Ratio

The film carriage is the assembly that carries the roll of machine-grade PE stretch film up and down the mast. Inside the carriage, the web passes over two rubber-covered rollers driven at different surface speeds. If the second roller turns 2.5 times faster than the first, the film is drawn out to roughly 2.5 times its original length — what many suppliers describe as a 150 percent stretch.

Three numbers describe the result:

  • Pre-stretch ratio: the elongation applied between the rollers. Higher ratios mean more meters of usable film per roll.
  • Post-stretch: the small additional elongation, often in the 10 to 15 percent range, that happens between the carriage and the load.
  • Force-to-load: the tension the film applies as it is laid onto the pallet, controlled separately from the ratio.

A film that is stretched too far necks down, thins at the edges and punctures easily. A film stretched too little stays thick but costs more per pallet. The film supplier’s data sheet, including tensile and puncture values measured under methods such as ASTM D882 and ASTM D5748, indicates where the practical ceiling sits for a given film.

Main Pre-Stretch Configurations Compared

Configuration How it works Typical stretch Best suited to Relative film cost
Brake carriage (no pre-stretch) Film tension comes only from a friction brake Minimal elongation Irregular, very heavy or fragile loads where gentle application matters Highest per pallet
Fixed mechanical pre-stretch Geared rollers set at one ratio at the factory Commonly in the 100 to 250 percent band depending on design Standard pallets with a stable film specification Moderate
Powered adjustable pre-stretch A separate motor drives the second roller; the ratio is set on the controller Adjustable, commonly up to around 250 to 300 percent with suitable films High-volume lines focused on film savings Lowest

Selection advice: choose powered adjustable pre-stretch if you wrap mixed loads or want to optimize film use per SKU. Fixed geared carriages suit single-product lines that buy one film grade. Brake-only carriages are acceptable for low daily volumes where film cost is secondary. Note that pre-stretched film, which arrives on the roll already elongated, works differently on the carriage — see our pre-stretched stretch film guide for that grade.

Matching Pre-Stretch to Film and Load

Pre-stretch is a joint property of the film, the machine and the load, and the three have to be matched.

  • Film type. Cast films generally run at higher ratios with quiet, controlled release, while blown films offer higher puncture resistance and are often run at moderate ratios. Confirm the recommended ratio with the film supplier before changing anything.
  • Load characteristics. Light, unstable or crushable loads need higher force-to-load but less aggressive stretch. Heavy, stable pallets tolerate the highest ratios. Sharp edges raise puncture risk, so a thin film stretched hard may not deliver the saving it promises.
  • Wrap pattern. Carriage speed versus turntable speed controls layer overlap. Too few revolutions leave banding gaps that containment force cannot close.

For how containment force translates into transport security, see our guide to pallet load stability for export packaging.

How to Tune Pre-Stretch Settings Step by Step

  1. Start from the film manufacturer’s recommended ratio and force values rather than the machine’s factory defaults.
  2. Wrap at least ten representative pallets at the starting settings and inspect top-layer hold, corner crush and banding.
  3. Raise the pre-stretch ratio in small steps while watching for edge tears, neckdown and film breaks.
  4. Set force-to-load per load type: higher for unstable pallets, lower for crushable goods.
  5. Adjust the wrap pattern so each layer overlaps evenly, and count revolutions per pallet.
  6. Record the final recipe in the controller, one per SKU or load family, and lock it against casual changes.

Common Pre-Stretch Mistakes Buyers Make

  • Buying the machine and film separately. A carriage tuned for one film may not suit another. Agree on film specifications and machine capabilities in the same negotiation.
  • Copying another plant’s settings. Ratios depend on film structure, gauge and carriage geometry; borrowed numbers usually under- or over-stretch.
  • Chasing maximum stretch. The saving comes from the highest ratio that still holds the load, not the highest ratio the carriage can produce.
  • Judging by roll price. Compare cost per pallet wrapped, not cost per roll. Our stretch film cost per pallet guide shows the calculation.
  • No stored recipes. Without per-SKU programs, operators improvise and film consumption drifts upward.

Specifications to Check Before Ordering

When comparing wrappers, ask the machine supplier to state these items in writing:

  • Pre-stretch ratio range and whether it is adjustable on the controller
  • Carriage drive type: brake only, fixed geared, or powered pre-stretch
  • Force-to-load control method and its adjustment range
  • Compatible film width, gauge range, maximum roll weight and diameter, and core size
  • Turntable or rotary arm load capacity and speeds
  • Recipe memory for storing settings per SKU
  • Power supply and air requirements for your factory

Throughput expectations belong in the same conversation; our guide to stretch wrapper cycle time and pallets per hour covers the calculation. Requirements may vary by application, market and applicable standard. For routine care of the carriage and rollers after commissioning, see the machine maintenance guide.

Frequently Asked Questions

Can I run any stretch film on a powered pre-stretch carriage?

No. Use machine-grade film rated for the carriage ratio. Hand-grade film tears or loses force, and mixed-spec rolls cause inconsistent containment. Confirm film and settings with the film supplier first.

What pre-stretch ratio should I choose?

Start at the film maker’s recommended ratio, commonly in the 150 to 250 percent band for machine film, then tune upward based on load containment and measured film use.

Does higher pre-stretch always save money?

No. Beyond the film’s limit you get neckdown, edge tears and rewraps. Savings come from the highest ratio that still secures the load reliably.

What is force-to-load?

It is the tension the film delivers to the pallet as it is applied. Higher values tighten unstable loads; excessive force crushes light or fragile goods.

Can settings be stored per pallet type?

On most PLC-controlled machines, yes. Recipe memory recalls wrap pattern, pre-stretch ratio and force-to-load for each SKU, which keeps consumption predictable.

How long does commissioning take?

Typically a few hours of trial wrapping across representative SKUs. Budget time to verify containment under transport conditions before locking the recipes.

Source Stretch Wrapping Machines from Pefilmpack

Weishan Litong Packing Material Co., Ltd. supplies automatic stretch wrapping machines together with machine-grade PE stretch film from the same supply chain, so carriage settings and film specifications arrive matched instead of negotiated separately. Turntable, rotary arm and fully automatic configurations can be matched to your pallet dimensions, power supply and throughput targets, and films can be customized in width, thickness, roll weight, core size and color.

To request a proposal, send us your product type, pallet size and load weight, wrapping method, target film specification, order quantity and destination port. Our team will reply with a machine configuration, a matching film recommendation and an export quotation.

Request a Quote

Shopping Cart