Meta description: How stretch film, PET strapping and BOPP tape work together to secure cargo inside export containers, with specifications, cost math and supplier checks.
Container load securing combines three consumables that are usually bought separately: stretch film to unitize pallets, PET strapping to restrain heavy or rigid cargo, and BOPP tape to keep cartons closed and film edges intact. Used as one system, they prevent the cargo movement that causes most container damage claims.
Table of Contents
- What Container Load Securing Actually Involves
- Where the Forces Come From
- The Three Tools and What Each One Does
- Matching the System to the Cargo
- Specifications to Fix in the Purchase Contract
- Cost per Container: Film Alone Versus Film Plus Strapping
- Six Load Securing Mistakes Buyers Keep Making
- How to Evaluate a Supplier for Container Work
- Frequently Asked Questions
- Source Container Packaging from Pefilmpack
What Container Load Securing Actually Involves
Securing a container load is not the same job as wrapping a pallet in a warehouse aisle. Inside a box that travels for weeks, cargo is exposed to repeated acceleration, engine and hull vibration, and condensation as the container moves between climate zones. Three failure modes account for most losses:
- Sliding and toppling. Pallets shift against each other until a stack collapses against the door end.
- Carton failure. Corners crush under stacking load, then the stack loses alignment and the film has nothing to hold.
- Moisture damage. Condensation drips onto unprotected cartons and film seams open along the way.
The commercial point is simple: film, strapping and tape are cheap relative to a rejected shipment. Buyers who treat them as three unrelated line items usually overpay for one and under-specify the other two.
Where the Forces Come From
Cargo restraint is designed against acceleration, not weight alone. Industry guidance, including the IMO/ILO/UNECE Code of Practice for Packing of Cargo Transport Units (CTU Code), uses planning values around 0.5 g to 0.8 g depending on mode, direction and trade lane. Confirm the figure your carrier or insurer expects rather than assuming one number.
Two conclusions follow. First, restraint has to act on the load itself: pushing a pallet against the container wall transfers force to a structure not designed as a tie-down point. Second, PE stretch film is a containment film, not a lashing. It integrates cartons into one unit so they cannot separate, but its tensile and puncture limits sit far below what a heavy load needs under 0.5 g of transverse acceleration.
The Three Tools and What Each One Does
Each consumable solves a different problem, and the specification follows from the job rather than from price per roll.
| Consumable | Primary job | Cannot do | Parameters to fix |
|---|---|---|---|
| Machine stretch film | Unitize cartons into one stable pallet; contain light and medium loads | Restrain heavy or rigid cargo; seal against water | Thickness, width, roll weight, core, pre-stretch rating, tack side |
| PET strapping band | Restrain palletized or rigid cargo; tie loads to fitting points | Hold loose cartons as a unit | Width, thickness, break strength, elongation, joint method |
| BOPP packing tape | Close cartons; seal film overlaps and reinforce film at sharp edges | Add structural strength to a stack | Width, total thickness, adhesive system, roll length |
A practical division of labor: film contains, strapping restrains, tape closes. Where cargo is both heavy and irregular, run strapping over the film with edge protectors at the corners.
Matching the System to the Cargo
Cartoned consumer goods on pallets
This is the classic film job. Machine film at roughly 17 to 23 micron, 500 mm wide on a 76 mm core, with 150 to 250 percent pre-stretch, contains a uniform pallet well. Add one or two PET straps per pallet only when cartons are slippery or the stack is tall and narrow.
Machinery and heavy equipment
Heavy units need a rigid base and direct restraint. Strap the machine to the pallet or skid first, then wrap with heavier film for dust and moisture, and use tape to keep the wrap closed. Never rely on film to stop a machine from moving.
Bagged and granular products
Bags settle and slumped stacks lose tension. Higher film force and a top cap help, and strapping at two heights reduces the settling effect. Where bags are dusty, specify reliable one-sided tack so layers bond.
Long goods and profiles
Bundles of profiles, pipes and timber are usually strapped rather than filmed, with film or a tape band closing the bundle ends. Check that strap edges are deburred, since PET strap under tension cuts into soft surfaces.
Specifications to Fix in the Purchase Contract
Vague purchase orders produce disputes at destination. Write measurable values with tolerances, and name the measurement method so both sides test the same way. Requirements may vary by application, market and applicable standard.
| Item | Write this in the RFQ |
|---|---|
| Stretch film | Thickness in micron with tolerance, width in mm, roll weight or wound length, core inner diameter, machine or hand grade, tack side, color, pre-stretch suitability |
| PET strap | Width and thickness in mm, break strength in daN or N with test method, elongation at break, surface finish, coil weight, joint system |
| BOPP tape | Width in mm, total thickness in micron including adhesive, adhesive system, roll length, core diameter, color, printing |
| All items | Pallet or carton configuration, label and shipping mark layout, batch coding, certificate of analysis if required |
Film specifications are best judged against ASTM D4649, the standard guide for selection and use of stretch wrapping film, using the thickness and width selection guide for the starting point, and verified on arrival with the checks described in this incoming inspection guide. Strap strength should be quoted with the test method attached; a bare number without a method is not a specification.
Cost per Container: Film Alone Versus Film Plus Strapping
Buyers often resist adding strapping because film alone looks cheaper. A worked comparison on a 40 ft container of 20 pallets exposes the balance; the figures are illustrative and must be recalculated with your own prices.
| Approach | Consumable per pallet | Relative cost | Typical outcome |
|---|---|---|---|
| Film only, light gauge | About 200 to 250 g of film | Lowest | Works for stable, uniform cartons; fails on tall or slippery loads |
| Film only, heavy gauge | About 350 to 450 g of film | Mid | Better containment but no restraint; film cost rises faster than protection |
| Film plus two PET straps | About 220 g of film plus roughly 6 to 8 m of strap | Mid to high | Restraint independent of film tension; recovers most of the film savings |
The honest comparison is cost per delivered pallet, which includes claim rate, rework at destination and customer chargebacks. One rejected container usually exceeds the annual strapping budget for that lane. The per-pallet method in this cost per pallet guide applies directly to the film side.
Six Load Securing Mistakes Buyers Keep Making
- Buying film by price per kilogram. A cheaper, thinner roll can cost more per pallet once breakage and rewrap are counted.
- Treating pre-stretch as free savings. Pushing ratio beyond the film’s capability thins the web, kills puncture resistance and causes load shift in transit.
- Using hand-grade film on an automatic wrapper. Hand film lacks the width and elongation consistency for high-speed carriages and will break at the clamp.
- Skipping the strap specification. Ordering “PET strap, standard” without width, thickness and break strength leaves the supplier to choose, usually downward.
- Ignoring the door end. The last pallets at the container doors take the highest dynamic load; plan bracing or a strap grid there rather than extra film everywhere.
- No photographic load record. Without dated photos of the finished load, a damage claim becomes an argument about how the container was packed.
How to Evaluate a Supplier for Container Work
- Range, not just one product. A supplier who makes film, strap and tape can advise on the combination and ship one consolidated order.
- Stated tolerances. Ask for thickness and width tolerance in writing, with the measurement method. A supplier who will not state tolerance is telling you something.
- Batch consistency. Request retained samples from two or three production batches; compare tack, color and thickness across them.
- Test reports with scope. Third-party reports should name the standard, the test conditions and the date. They confirm a sample, not every future shipment.
- Export packing discipline. Roll orientation, pallet height, moisture barrier and shipping marks decide whether the goods arrive usable.
- Lead time under peak pressure. Ask how capacity is allocated in the pre-holiday quarter, when every exporter orders at once.
Frequently Asked Questions
Can I secure a container load with stretch film only?
For uniform, light and medium cartoned pallets, film alone often keeps the load integrated. For heavy, tall, slippery or irregular cargo, film provides no restraint and should be combined with strapping or bracing.
How much film does one pallet need?
Consumption depends on pallet size, wrap pattern, overlap and pre-stretch. A typical cartoned pallet takes roughly 200 to 400 g, but the number should be measured on your own wrapper rather than taken from a table.
Which strap is right for export containers?
PET strap is the usual choice: it does not rust, holds tension on rigid loads and is available in a range of widths and break strengths. Steel remains relevant for very heavy or sharp cargo, but adds handling and disposal issues.
Does BOPP tape add any strength to a load?
Not structurally. Its role is to keep cartons closed, seal film overlaps and reinforce film where it crosses straps or sharp edges. Specifying tape as a strength component leads to under-built loads.
Can the three items ship in one container?
Yes. The three items can be consolidated on pallets with mixed items clearly marked, which lowers freight cost and simplifies receiving. Ask for a loading plan before confirming.
What should a first trial order include?
One pallet quantity of each item in the intended specification, plus a documented load trial with photos. Compare arrival condition, not just the price list, before committing to volume.
Source Container Packaging from Pefilmpack
Weishan Litong Packing Material Co., Ltd. (Pefilmpack) supplies the consumables that hold export loads together: PE stretch film in hand and machine grades, PET strapping band, BOPP packing tape and PE protective film. Width, thickness, length, roll weight, color and core size are customized to the application, and export-grade packing is standard. Because the range comes from one factory, buyers can consolidate film, strap and tape into a single shipment with consistent quality control from trial order to repeat volume.
Send your load type, pallet dimensions, film specification, strap strength requirement, tape width and destination port through the contact page, and the factory will confirm the combination and quote against your actual consumption.
Build one securing system, not three separate line items. Send Your Specifications to Pefilmpack.