Meta description: What post-consumer recycled content changes in PE stretch film, how to compensate with gauge, verify recycled claims and specify a PCR grade that still wraps.
Recycled content in PE stretch film changes more than the sustainability statement on the carton. Post-consumer resin alters puncture resistance, elongation, color and odor, and those changes decide whether the film still runs on your wrapper. This guide explains what the percentage actually means and how to specify a grade that performs.
Table of Contents
- What Recycled Content Means on a Stretch Film Datasheet
- How Recycled Resin Changes Film Behavior
- Compensating with Gauge and Structure
- Recycled Grades and What Each One Suits
- Cost: Premium, Fees and Cost per Pallet
- Verifying a Recycled Content Claim
- Common Buying Mistakes
- How to Evaluate a Recycled Film Supplier
- Frequently Asked Questions
- Source Recycled Stretch Film from Pefilmpack
What Recycled Content Means on a Stretch Film Datasheet
A recycled content figure is only meaningful with three qualifiers: the source of the material, the percentage, and the basis of calculation.
Source. Post-consumer recyclate (PCR) comes from material that has completed a consumer life, typically collected LDPE film and bags. Post-industrial recyclate (PIR) comes from factory scrap, trim and off-spec production. PCR carries the stronger environmental story and the wider quality variation; PIR is cleaner and closer to virgin resin in behavior.
Percentage. The number usually refers to the share of recycled resin by weight in the total polymer content, not in the finished roll. Additives, colorants and the paper core are normally excluded. Ask which basis the supplier is quoting.
Layer. In a three-layer co-extruded film, recycled resin is often placed in the core layer, with virgin resin on the surfaces that carry tack and contact the load. The same total percentage can therefore describe very different films.
How Recycled Resin Changes Film Behavior
Recycled polyethylene has a broader molecular weight distribution and contains traces of foreign polymer, print ink and moisture. The practical consequences are consistent across the industry, though the size of each effect varies by source and sorting quality.
| Property | Typical change with recycled content | Where it shows up |
|---|---|---|
| Dart impact (ASTM D1709) | Lower and more variable | Film punctures on carton corners and pallet edges |
| Tensile strength and elongation (ASTM D882) | Moderately reduced | Less stretch before break; more attention needed at the carriage |
| Tear resistance (ASTM D1922) | Often reduced | Small nicks propagate into full-width splits |
| Gels and fisheyes | More frequent | Visual defects, weak points, print or label issues |
| Color and haze (ASTM D1003) | Yellow or grey cast, higher haze | Load identification, barcode scanning, retail presentation |
| Odor | Possible residual smell | Rules the grade out for food-adjacent and consumer-facing packs |
| Tack consistency | Less predictable | Layer-to-layer bonding and load integrity after transit |
The important reading is that recycled content mainly attacks puncture and tear performance, which are exactly the properties that fail first on real pallets. A film that tests acceptably on a flat surface can still split at a carton corner in transit.
Compensating with Gauge and Structure
The standard remedy is a gauge increase, because puncture resistance rises faster than linear with thickness. Moving from 17 to 20 micron, or 20 to 23 micron, recovers much of the lost impact performance at modest material cost.
Structure matters as much as gauge. A three-layer construction lets the converter put recycled resin in the core and keep virgin, high-tack resin on the surface. That protects the properties that touch the load while retaining the recycled content claim. Where the wrapper runs at high pre-stretch ratios, a recycled grade should be specified with a lower recommended ratio; pushing recycled film to the same stretch as a virgin grade is the most common cause of unexplained breakage. The ratio and force settings themselves are covered in this pre-stretch settings guide.
Thickness tolerance deserves attention too. Recycled resin flows differently, and a film sold as 20 micron with a wide minus tolerance behaves like a thinner film everywhere. Specify the tolerance and the measurement method. Requirements may vary by application, market and applicable standard.
Recycled Grades and What Each One Suits
Entry recycled grades, roughly 15 to 30 percent
These behave close to virgin film and usually run on existing wrappers without parameter changes. Suitable for general export pallets, distribution center work and buyers who need a documented recycled figure without changing operations.
Mid recycled grades, roughly 30 to 50 percent
Puncture and tear performance diverge enough to require a gauge step and a pre-stretch review. A reasonable fit for stable, uniform cartoned loads handled by automatic wrappers with controlled force settings.
High recycled grades, above 50 percent
These are specialty products. Expect visible color variation, more gels and a narrower processing window. They suit buyers with a specific customer requirement, a captive wrapping line that can be tuned, and cargo that is not sharp-edged or heavy.
Post-industrial grades
PIR film sits between virgin and PCR in behavior and is often chosen when a customer accepts industrial scrap as the recycled source. Verify what the buyer’s specification actually allows before quoting PIR as recycled content.
Cost: Premium, Fees and Cost per Pallet
Recycled stretch film is not automatically cheaper. Clean PCR feedstock competes for limited supply, and sorting plus filtration add processing cost, so recycled film often carries a premium over virgin machine film, while lower-grade PCR can trade at or below virgin pricing.
Three cost lines decide the real answer:
- Material premium or discount per kilogram, against standard machine grade film of the same width.
- Gauge compensation: the extra microns needed to match puncture performance, which raises grams per pallet.
- Fee and compliance value: extended producer responsibility fee modulation and customer scorecards can offset a material premium, but the value sits with the buyer’s market, not with the film.
The comparison that holds up is cost per pallet at equal performance, calculated with the method in this cost per pallet guide. A recycled film at a 10 percent premium with a one-step gauge increase can still win if it removes a packaging levy or satisfies a retail requirement, and can lose badly if it doubles breakage on a fast line.
Verifying a Recycled Content Claim
Recycled content is an invisible property, so verification is documentary and procedural rather than visual.
- Mass balance. The supplier books recycled feedstock into a production system and allocates the credit across output. Widely used, but the physical film may contain less recycled resin than the claim states.
- Segregated or physical segregation. Recycled material is kept in a separate stream and the film physically contains the stated share. Stronger claim, higher cost.
- Chain of custody documents. Look for feedstock supplier declarations, transaction records and batch-level statements linking a production lot to a recycled input.
- Batch testing. Ask for dart impact and tensile results per batch, not a single type test from a year ago; the checks in this incoming inspection guide show what can be verified on arrival.
Ask which model the supplier uses, and make sure your own customer accepts the same model. A mass balance claim presented as physically segregated content is a credibility problem that surfaces at audit, not at delivery.
Common Buying Mistakes
- Ordering the same gauge as virgin film. The film punctures earlier, breakage rises, and the recycled program gets blamed for a specification error.
- Treating the percentage as interchangeable across suppliers. Twenty percent of one feedstock is not twenty percent of another; the source and sorting quality drive performance.
- Ignoring color and haze. A grey cast can break barcode scanning and load identification in automated warehouses.
- Using recycled film for food-contact or retail-facing packs without checking the specification. Odor and migration questions belong in the compliance discussion, not the receiving dock.
- Accepting a claim without a custody model. “Recycled” without mass balance or segregation documentation will not survive a customer audit.
- Changing film without retuning the wrapper. Pre-stretch ratio and force-to-load settings carried over from virgin film cause most of the failures reported in the first month.
How to Evaluate a Recycled Film Supplier
- Feedstock control. Ask where the recyclate comes from, how it is sorted and what filtration level the line runs.
- Stated content basis. Percentage by weight of polymer, which layer, and which custody model.
- Batch data. Dart impact, tensile and elongation results per lot, with the test standard named.
- Consistency between batches. Color and gel count are the visible signals; request retained samples from consecutive lots.
- Honest limits. A supplier who says which applications the grade is not suited for is more useful than one who claims universal performance.
- Trial support. Sample rolls sized for a real shift on your wrapper, plus recommended pre-stretch settings.
Frequently Asked Questions
Does recycled stretch film break more easily?
It can. Recycled resin typically reduces dart impact and tear resistance, so film at the same gauge breaks more readily on sharp corners. A one-step gauge increase and a slightly lower pre-stretch ratio usually close the gap.
Can recycled film run on an automatic wrapper?
Yes, provided the grade is specified for machine use and the wrapper settings are adjusted. Hand-grade recycled film should not be substituted on an automatic line.
Is recycled film suitable for food packaging?
Only with an explicit food-contact specification covering the recycled stream and the applicable regulation. Many recycled grades are intended for secondary and transport packaging rather than direct food contact.
Why is recycled film sometimes more expensive?
Clean, food-grade PCR feedstock is limited and sorting plus filtration add cost. Pricing also depends on gauge compensation. Some grades trade below virgin film, particularly lower-specification PCR.
How do I prove the recycled content to my customer?
Request the custody model, feedstock declarations and batch records, and confirm your customer accepts that model. Mass balance and physical segregation are not interchangeable claims.
Can I get samples before ordering?
Yes. Ask for rolls in the intended width and gauge, run a full shift, and compare breakage, wrap appearance and grams per pallet against your current film before setting volume.
Source Recycled Stretch Film from Pefilmpack
Weishan Litong Packing Material Co., Ltd. (Pefilmpack) produces PE stretch film for export and industrial buyers, including grades formulated with recycled resin alongside standard virgin machine and hand film. Width, thickness, roll weight, core size, color and packing configuration are customized to the application, and pre-stretch recommendations are supplied with each grade so the film performs on the wrapper it was bought for. Factory-direct supply, export-grade packing and OEM support keep specifications stable between the trial order and repeat shipments.
Send your required recycled content, application, load type, film dimensions and destination port through the contact page, and the factory will confirm which grade fits and supply samples for a line trial.
Specify recycled content without losing load performance. Ask for a Sample from Pefilmpack.