Meta description: PET strapping for bales: how width, thickness, tension and joint type decide whether a cardboard, textile or plastic bale survives stacking and transport.
Baling strap has one job: hold a compressed bale at its compressed density while it is handled, stacked and shipped. PET strapping band is the usual choice for cardboard, textile and plastic bales because it combines high break strength with enough elasticity to follow a bale that relaxes. This guide covers the strap specifications, tension settings and joint choices that keep bales intact to destination.
Table of Contents
- What a Baling Strap Actually Has to Do
- PET vs PP vs Steel for Bales
- Choosing Width, Thickness and Break Strength
- Strap Count, Pattern and Tension
- Tools and Joints on a Baling Line
- Cost per Bale: A Worked Example
- Common Buying Mistakes
- How to Evaluate a PET Strap Supplier
- Frequently Asked Questions
- Source PET Strapping Band from Pefilmpack
What a Baling Strap Actually Has to Do
A bale is a spring under load. Material is compressed, strapped, then released from the press, at which point it tries to expand. The strap must resist that expansion for weeks, through fork handling, double stacking, truck vibration and humid storage.
Three failure modes account for most bale losses:
- Break at the joint or at a sharp edge, where the strap is cut rather than pulled apart.
- Creep, where the strap stretches slowly under sustained tension and the bale loosens without any visible damage.
- Edge cut, where the strap slices into the bale corner and loses tension as the corner collapses.
Each failure mode points to a different specification decision, which is why strap selection for baling cannot be reduced to picking the highest break strength on the datasheet.
PET vs PP vs Steel for Bales
| Property | PET strapping | PP strapping | Steel strapping |
|---|---|---|---|
| Break strength for a given width | High | Moderate | Highest |
| Elastic recovery | Good; holds tension on relaxing bales | Higher stretch, weaker recovery under long load | Almost none |
| Behavior on a relaxing bale | Stays tight as the bale settles | Tends to loosen | Stays tight but can crush the bale |
| Edge damage risk | Low to moderate | Low | High without edge protection |
| Handling safety | Safe; no recoil injury | Safe | Requires gloves and face protection |
| Corrosion | None | None | Rusts in humid storage |
| Disposal | Recyclable with PET stream | Recyclable with PP stream | Scrap metal |
For most recycling and fiber operations, PET is the default. PP suits light bales consumed quickly, such as in-plant transfer bales. Steel remains appropriate for dense metal scrap, where its lack of elasticity is an advantage rather than a defect.
Choosing Width, Thickness and Break Strength
Break strength is a function of cross-section: width multiplied by thickness. Two consequences follow, and both matter commercially.
First, a wider strap at a thinner gauge can match the break strength of a narrower, thicker strap while spreading load across the bale corner and reducing edge cut. Second, the same break strength bought as a narrow strap is usually cheaper per metre, which is why narrow straps are common in plants that then suffer corner failures.
Start from the bale, not the strap. Estimate the expansion force of the bale at its compressed density, then apply a safety factor. A 2:1 safety factor is a common starting point for static storage; 3:1 is more appropriate where bales are double stacked or handled repeatedly.
- Width. Narrow straps in the 12–16 mm range suit light, well-formed bales. Fiber and cardboard bales in the 400–1,000 kg range generally call for 16–19 mm, with wider straps where corners are soft.
- Thickness. Commonly 0.6–1.2 mm for baling duty; heavier sections where the bale is dense and the strap run is short.
- Surface. Embossed strap grips the bale and joint better; smooth strap feeds more freely through automatic heads, which usually makes it the practical choice on long automatic lines.
- Elongation. PET stretches less than PP under the same tension and recovers more of it, which keeps a relaxing bale tight.
Requirements may vary by application, market and applicable standard, so treat these ranges as a starting point for a trial rather than a specification.
Strap Count, Pattern and Tension
Most bale failures in the field are pattern failures, not material failures. Four straps on a rectangular bale, arranged as two longitudinal and two transverse, is the common baseline for fiber bales. Denser bales and longer bales need more.
A practical rule: increase strap count until a bale lifted by its top straps shows no visible sag along its length. Sag means the strap count, the tension or the pre-compression is wrong.
Tension is the other half of the equation, and over-tensioning is a common error. A strap tensioned far beyond what the bale needs cuts the corner, crushes the outer layers, and breaks at the joint when the bale is dropped. Set tension from bale behavior, then record the setting so it repeats across shifts.
Edge protection matters on any bale with a soft or sharp corner: edge boards spread the load and cost less than the rework a burst bale causes.
Tools and Joints on a Baling Line
Joint efficiency, meaning the share of strap break strength retained at the joint, decides the real strength of the system. A strap rated at 600 kg that loses a third of its strength at the seal is a 400 kg strap.
- Manual tensioner with metal seals. Lowest equipment cost, highest labor per bale, and joint quality depends entirely on operator technique.
- Battery-powered combination tools. Tension, seal and cut in one pass. Consistent tension and a repeatable friction-weld joint; the practical choice for mid-volume plants.
- Fully automatic baling machines. Highest throughput, tightest tension consistency, and the least tolerance for strap variation in width or thickness. Automatic heads are unforgiving about strap camber and surface finish.
If you may move from manual to automatic later, specify the strap for the automatic head from the start: a strap that hand-feeds well is not automatically an automatic-machine strap. Our guide to PET strapping tools and joints covers joint testing in more detail.
Cost per Bale: A Worked Example
Strap price per kilogram hides the only number that matters: cost per bale shipped intact. The calculation is straightforward.
- Measure strap length consumed per bale, including the tail and the joint overlap.
- Multiply by strap mass per metre, which comes from width, thickness and PET density.
- Multiply by price per kilogram.
- Add edge protection, labor per bale, and the cost of rework on failed bales.
As an illustration only: a fiber bale using four straps at 3.2 m each, on 19 mm × 1.0 mm PET strap at roughly 27 g per metre, consumes about 350 g of strap per bale. At USD 2.10 per kilogram that is approximately USD 0.73 per bale. Moving to a narrower 16 mm strap saves around 15%, or about USD 0.11, but raises corner-failure risk on a dense bale. On most lines strap cost is the smaller half of the equation once rework is counted.
Common Buying Mistakes
- Buying on break strength alone. Joint efficiency and edge behavior decide whether that strength is usable.
- Downgrading width to save cost. The saving is real per metre and usually lost to corner failures.
- Ignoring strap camber. A strap with excessive curvature jams automatic heads and causes misfeeds at three in the morning.
- Mixing suppliers mid-line. Two straps with the same nominal dimensions can behave differently in the same head.
- Over-tensioning to compensate for a weak pattern. Fix the pattern, then set tension.
- Storing strap in direct sun. UV exposure degrades PET over time; keep coils shaded and off concrete floors.
How to Evaluate a PET Strap Supplier
- Ask for the dimensional tolerance on width and thickness, not the nominal size. Automatic heads fail on tolerance, not on average.
- Request break strength and elongation data with the test method named, and check whether the figures are typical or minimum.
- Confirm embossed or smooth surface as a deliberate choice, not as whatever the line happened to run.
- Ask how coils are wound and packed for export: coil weight, core, wrap and pallet configuration all affect damage in transit.
- Ask for a trial coil in your exact specification before committing to a container, and run it on your own head.
- Check whether the supplier also stocks the PET strapping band grades used elsewhere in your plant, so tolerances stay consistent.
Frequently Asked Questions
Is PET strap strong enough for a 1,000 kg cardboard bale?
Usually yes, at adequate width and thickness with a proper pattern. A 19 mm strap at 1.0 mm section is commonly used on bales in that range. Confirm with a trial on your press, because bale density, not weight alone, sets the expansion force.
Why do my bales loosen after a few days?
Creep, or a pattern that was already marginal. PET recovers well, but no strap holds a bale that was under-compressed or under-strapped. Check compression first, then strap count, then tension.
Can I use PP strap for baling instead?
For light bales consumed within days, yes. For bales that are stacked, stored or shipped, PP relaxes more and tends to loosen. See our comparison of PET versus PP strapping for the trade-offs.
What causes strap breakage at the joint?
Three causes dominate: incomplete weld from worn or misadjusted tooling, tension applied before the joint is fully formed, and strap that is too thick for the seal or weld cycle. Joint strength should be checked by sampling, not assumed.
How should strap be stored?
Shaded, dry, off the floor, and away from heat sources. Coils stored in direct sunlight or high humidity lose strength faster and jam automatic heads.
Can PET strap be recycled with the bale?
PET strap is recyclable in a PET stream, but it must be separated from the bale material before repulping. On fiber bales, strap is normally cut and collected at the receiving plant.
Source PET Strapping Band from Pefilmpack
Weishan Litong Packing Material Co., Ltd. supplies PET strapping band in embossed and smooth surfaces, with width, thickness, coil weight, core size and color made to order for baling, palletizing and export bundling. Because the same factory also produces stretch film, BOPP packing tape and shrink film, buyers consolidating packaging consumables can source a full container mix from one supplier instead of three. Specifications are quoted with tolerances stated explicitly, so the strap you approve at sample stage is the strap that arrives. Export packing is configured for sea freight, and OEM branding is available on request.
Send your strap width, thickness, surface type, coil weight, estimated bales per day and destination port for a quotation. If you are moving from manual to automatic baling, tell us the machine model so the strap is specified for that head.