Horizontal Stretch Wrapping for Coils, Pipes and Long Goods

Meta description: How horizontal orbital stretch wrapping works for coils, pipes and long goods, with film selection, machine settings, overlap targets and buying checks.

Table of Contents

What Is Horizontal Stretch Wrapping?

Horizontal stretch wrapping, often called orbital wrapping, is a method in which a long product passes through a rotating ring of stretch film while the product itself moves forward. The rotating ring lays the film down in a helical path, so a continuous band of film covers the entire length of the item. On a conventional pallet line the load rotates; here the product travels and the ring does the work.

For importers of cable, pipe, profile and panel products, this distinction matters commercially. Horizontal wrapping protects long goods from dust, scuffing and light moisture during warehouse handling and container transport, and it gives a clean, presentable pack for goods that are simply too long or too awkward to wrap on a turntable. If you buy or convert long products and currently band, bag or crate them, this article explains where orbital film wrapping fits and what to check before you commit.

Which Products Suit Horizontal Wrapping?

Orbital wrappers earn their place on lines where the product is long, relatively rigid and fed end-to-end. Typical applications include:

  • Wire and cable coils. The helical film band holds loose coil ends in place and stops the outer wraps from unraveling during shipping.
  • Steel, copper and plastic pipe. Film protects polished or coated surfaces from abrasion against each other and against the conveyor.
  • Aluminum extrusions and uPVC window profiles. A soft, even band of film prevents scratching on visible surfaces without leaving adhesive residue the way self-adhesive tape can.
  • Textile beams and yarn spools. Low, controlled tension keeps film coverage secure without crushing soft winding edges.
  • Doors, panels and flat boards. Edge protection and dust sealing for goods stacked on edge or fed flat through the ring.
  • Lumber, moldings and floor planks. Bundling of random lengths into a single, unitized pack that lifts and loads safely.

The common thread is geometry: if the product is longer than it is wide and can pass through a ring, orbital wrapping usually beats hand wrapping on speed and consistency.

How the Film Is Applied

Although machines differ by brand, the film path follows the same sequence, and each step affects a purchasing decision:

  1. Product entry. The item is fed onto rollers or a conveyor and passes into the ring opening. Product dimensions define the ring size you need, which in turn defines the film width the machine is designed for.
  2. Ring rotation. The film carriage or ring spins around the product. Ring speed and line speed together determine how many film layers land on each section of the product.
  3. Film tensioning. The film is pulled against a brake or pre-stretch roller set. Tension controls both the elongation achieved and the containment force on the product; too much tension crushes soft goods, too little lets the pack loosen.
  4. Helical lay-down. As the ring turns, the product advances, so each revolution overlaps the previous band. Overlap percentage is the main lever for coverage and film consumption.
  5. Cut and tail securing. At the end of the cycle the film is cut and the tail is clamped, tucked or heat-sealed. A loose tail is the most common cause of packs unwinding in transit.
  6. Finishing. Some lines add end caps, corner boards or a strapping band after wrapping, especially for heavy coils and bundles destined for sea freight.

Choosing Stretch Film for Horizontal Wrappers

Machine-grade film is the default for orbital machines. Because the film is applied at a set tension rather than stretched aggressively around a pallet, the elongation requirement is lower than for pallet wrapping, and most lines run standard machine film successfully. What changes is the emphasis on other properties:

  • Width. Orbital machines commonly run 300 mm to 500 mm film; 500 mm is the most common width for coils, pipes and bundles. Confirm the machine’s film width spec before ordering, since a mismatch forces re-slitting or poor tracking.
  • Thickness. Industry practice on orbital lines typically falls between 15 and 25 micron. Lighter profiles run thinner film; heavy coils and sharp-edged steel go heavier. Requirements may vary by application, market and applicable standard.
  • Tack and tail behavior. The cut tail must hold through transport. A film with reliable one-sided cling anchors the tail without transferring sticky residue to the product surface.
  • Puncture and tear resistance. Pipe cut ends, burrs and sharp profile edges are the main failure points. For those loads, buyers often prefer blown film; for clean aluminum and plastics, cast film offers clarity and quieter unwind.
  • Surface friendliness. On visible or coated surfaces, ask for a film that unwinds cleanly and does not mark finishes, and test on real product before scaling up.

If you also run a pallet line, do not assume one film serves both. Pallet film is optimized for force-to-load and vertical containment; orbital film is optimized for tracking through the ring and tail anchoring. Where the same warehouse uses both, many buyers keep two specifications and order them separately from the stretch film range.

Machine Settings That Shape Film Choice

Film and machine settings interact, so film selection should not be made in isolation:

  • Ring speed and line speed. Faster relative speeds demand a film that tracks well at speed without wandering off the product centerline.
  • Overlap percentage. Commonly set between roughly 20% and 50% depending on how much protection and moisture sealing the load needs. Higher overlap raises film consumption directly, which is why cost-per-pack calculations should be based on meters used per item, not roll price.
  • Tension and pre-stretch settings. A machine that pre-stretches film before the ring can run thinner film at the same containment force; if you later change film brand or gauge, re-check these settings.
  • Product weight and rigidity. Soft bundles deform under tension, so flexible loads need lower tension and sometimes more overlap to stay sealed.

Confirm the machine’s design limits with its supplier, then run a supervised trial with your actual product before finalizing a film specification.

Film Specifications by Product Type

The table below summarizes common starting points reported in industry practice. Treat them as a first draft for trials, not final values.

Product type Typical film width Typical thickness Key film property Notes
Wire and cable coils 500 mm 15–23 micron Dependable cling for tail anchoring Overlap secures loose coil ends
Steel and plastic pipe 500 mm 17–25 micron Puncture resistance at cut ends Drop-impact checks such as ASTM D1709 help compare films
Aluminum and uPVC profiles 300–500 mm 15–20 micron Clean unwind, no surface marking Test on coated or anodized finishes
Textile beams and yarn spools 300–500 mm 15–20 micron Soft, controlled tension Lower overlap to avoid crushing winding edges
Doors, panels and lumber 500 mm 20–25 micron Tear resistance at board edges Consider corner protection on heavy packs

Common Buying Mistakes

  • Reusing pallet film spec on the orbital line. Tracking and tail behavior differ; trial separately.
  • Judging film by roll price only. A cheaper roll that needs more overlap can cost more per wrapped item.
  • Buying one thickness for every product. Coils and profiles have very different edge risks.
  • Skipping a trial on real product. Sample tests on a clean bench rarely predict how film behaves at ring speed on dusty steel.
  • Ignoring tail securing in the spec. Ask how the machine cuts and holds the tail, and whether the film’s cling supports it.
  • Overlooking storage conditions. Packs stored outdoors need UV-stable film; hot or cold storage changes cling and tension behavior.

Frequently Asked Questions

Can I use the same film as my pallet wrapper?
Often yes for light products, but orbital lines stress tracking and tail anchoring differently. Run a trial before consolidating specifications.

What film width do orbital machines need?
Most run 300 mm to 500 mm, with 500 mm common for coils and bundles. Match the machine’s specification; do not assume pallet widths transfer.

How much overlap should I set?
Commonly 20% to 50% depending on protection needed. Start mid-range on trial packs and adjust for dust sealing or film savings.

Will the film scratch sensitive surfaces?
Quality machine film unwinds without marking. For coated or anodized finishes, request a surface-friendly grade and test on production parts.

Can thickness and width be customized?
Yes. Factories that extrude their own film routinely cut custom widths and gauges, usually with a minimum order quantity per specification.

What should I include in a film RFQ?
Product type and dimensions, machine make and film width, target thickness, tensile and puncture expectations, order quantity, and destination port.

Source Stretch Film from Pefilmpack

Weishan Litong Packing Material Co., Ltd. (Pefilmpack) manufactures PE stretch film for pallet and industrial wrapping, including machine grades suited to orbital and horizontal wrapping lines. As a factory-direct exporter, the company supports custom width, thickness, length, roll weight, core size and color, with export packaging and OEM support for international buyers. Whether you wrap cable coils, extruded profiles or timber bundles, specifications can be matched to your machine and trial-tested before volume orders. If you need film for a specific orbital machine, review the machine film details or send your specifications with product dimensions, machine model, target thickness, order quantity and destination port.

Shopping Cart