PET Strapping Band: Width, Thickness and Break Strength

Meta description: Width, thickness and break strength are quoted together but rarely compared correctly. Learn how PET strapping specs interact, how to size a strap to a load, and what to verify.

Table of Contents

What the Three Specifications Describe

PET strapping band is specified by width, thickness, and break strength, and those three numbers are not independent. Width and thickness define the cross-section that carries the load. Break strength defines how much tensile force that section withstands before it fails. A quote that lists width alone, or break strength alone, cannot be evaluated.

Strap is a load-bearing component, not a consumable accessory. Under-strength strap fails in transit, and a failed strap on a pallet of cartons or building materials usually means a damaged load, a rejected delivery, and a claim. Over-specified strap costs more per meter and can crush light products when the tensioner is set to suit the strap.

How Width, Thickness and Strength Interact

Break strength scales roughly with cross-sectional area, which is width multiplied by thickness. This produces a rule buyers get wrong regularly: a wider strap is not automatically stronger. A 19 mm strap at 0.6 mm has less material in section than a 16 mm strap at 1.0 mm, and it breaks at a lower force.

Two factors modify the relationship. Orientation: PET strap is extruded and stretched, and the orientation along its length gives high tensile strength with low elongation, so a nicked edge reduces strength sharply. Thickness tolerance: strap is measured with a caliper at several points on the coil, and a band at the low end of tolerance loses strength in proportion.

Break strength is normally quoted in newtons or kilograms-force. Market ranges run from roughly 2,000 N on light 12 mm grades to above 10,000 N on heavy 32 mm grades, but these describe the market rather than any one product. Requirements may vary by application, market and applicable standard.

Common Strap Widths and Where They Fit

12 mm to 16 mm

Narrow strap suits light and medium loads: carton bundles, small crates, printed materials, and light building products. It is also the width used on automatic strapping machines in distribution centers, where strap must run through a narrow arch at high cycle rates. Because force concentrates on a small area, edge protectors are often needed on soft or printed surfaces.

19 mm

19 mm is the general-purpose width for palletized industrial goods, brick and block, metal sections, and bundled timber. It balances strength against cost and stays manageable with hand tools. Most manual tensioner and sealer sets are built around this width, making it the practical default.

25 mm

25 mm is used where loads are heavy or where strap must bridge an uneven surface without cutting in. It is common on heavy pallets, machinery, and construction materials, and it pairs with higher-tension tools. The wider band spreads pressure, which reduces indentation on semi-rigid products.

32 mm and above

Heavy-duty widths serve steel coils, heavy machinery, and loads where one strap carries a large share of the weight. They need powered tensioning and matching seals, because hand tools rarely reach the tension that makes the extra strength useful.

Surface Finish and Strap Stiffness

PET strap is supplied smooth or embossed. Embossing adds texture that raises friction against cartons and against itself at the joint, reducing slippage on smooth or shrink-wrapped surfaces. Smooth strap prints more cleanly and runs with less friction through automatic arches, but it grips less on polished loads.

Stiffness is the property buyers notice after delivery rather than on the quote. PET is stiffer than PP at equal width, which helps it feed through automatic machines, but a stiffer strap springs back when cut. On a small radius corner, a very stiff heavy strap may bridge the corner instead of seating against it, so the load still shifts.

Break Strength Versus Working Load

Break strength is a laboratory figure for a new, undamaged strap pulled in a straight line. Working load is what you allow the strap to carry in service, and it is always lower. The difference is the safety factor, which accounts for edge damage, joint efficiency, load settling, vibration, and impact.

A common starting point is a factor of about two for static storage and at least three for road, rail, or sea freight. Sharper edges, heavier loads, and longer transit favor a higher factor. The calculation is simple: load weight divided by the number of straps, multiplied by the safety factor, then compared with break strength.

Load situation Typical starting width Notes on selection
Cartons and light bundles, indoor storage 12–16 mm Lower safety factor acceptable; watch edge cut on printed cartons
General palletized goods, export containers 19 mm Default industrial width; edge protectors on soft surfaces
Brick, block, timber, metal sections 19–25 mm Higher safety factor; check the strap does not cut the product
Heavy machinery and dense loads 25–32 mm Powered tensioning; verify the joint method before approving
Long-radius or irregular loads 25 mm and above Strap must seat on the surface, not bridge a corner

The table is a starting point for a trial, not a substitute for a load test. Requirements may vary by application, market and applicable standard.

Joint Efficiency

The joint is the weakest point in any strap system, and it is usually missing from the quotation. PET strap is normally joined by friction welding with a hand or pneumatic tool, or by metal seals. A correctly set friction weld retains a high proportion of break strength, but the same tool set for a thicker band will under-weld and lose strength with no visible sign.

This is why joint testing matters more than the headline rating. A strap rated at 8,000 N with a joint holding 60 percent gives an effective system strength of about 4,800 N, and that figure governs the load. Ask which joint method the recommended working load assumes, and test joints on your own tooling.

Specifications to Confirm in an RFQ

  1. Width and thickness in mm, each with the accepted tolerance.
  2. Break strength in N or kgf, with the test method and sample condition stated.
  3. Elongation at break, and retained tension after 24 hours.
  4. Surface: smooth or embossed, with pattern depth if embossed.
  5. Color, and whether it is masterbatch or surface printed.
  6. Coil weight, coil inner diameter, and core material.
  7. Joint method intended for the application, and the tooling available on site.
  8. Packaging: coils per carton, cartons per pallet, pallet height, shipping marks.
  9. Order quantity, trial order intention, and destination port.

Where strap will run on an automatic machine, add the arch size, machine make, and cycle rate. Strap that performs by hand can fail to feed if stiffness or winding does not match the machine.

Common Purchasing Mistakes

  • Comparing price per kilogram. Two coils of equal weight hold very different meters when width and thickness differ; cost per meter is the only comparable figure.
  • Assuming wider means stronger. Cross-section, not width, determines break strength.
  • Accepting nominal thickness without tolerance. The low end of a wide band removes strength quietly.
  • Using PP tools on PET strap. PET needs higher tension to perform.
  • Ignoring the joint. The seal, not the strap, decides most field failures.

How to Verify Strap Quality Before Shipment

Most of the specification can be checked before the container is sealed.

  1. Measure width and thickness with a caliper at three points along the coil and record the minimum thickness.
  2. Weigh several coils against declared weight to detect short-length winding.
  3. Cut a sample and inspect the cross-section for voids, bubbles, or uneven edges.
  4. Pull a joint on your own tooling to destruction and compare with the supplier’s stated figure.
  5. Check coil inner diameter, winding alignment, and strap end fixing, since a loose coil jams automatic feeders.
  6. Confirm carton labels and shipping marks against the order.

Frequently Asked Questions

What width of PET strap do I need for a one-ton pallet?

There is no single answer, because strap count and safety factor drive the result more than width. A common approach is four 19 mm straps on a well-formed load, then a trial. Heavy or sharp-edged loads move to 25 mm or wider.

Is PET strap stronger than PP strap?

At equal cross-section, PET generally has higher tensile strength and much lower elongation, so it holds tension longer on a settling load. PP stays adequate and cheaper for light, stable loads. See our PET versus PP strapping comparison.

Can I use metal seals with PET strap?

Yes, though friction welding is more common. Seal choice must match width and thickness, because an undersized seal crimps the edge and creates a stress point. Test the joint rather than trusting the strap rating.

How much strength does the joint lose?

It depends on tool setting and strap thickness. A correctly set weld retains most of the break strength; a poorly set weld can lose a large share with no visible defect. Verify it on your own equipment.

Can width, thickness and color be customized?

Yes. Width, thickness, break strength grade, color, coil weight, and coil core are specified per order in factory-direct supply. Custom grades are normally confirmed against a sample and a joint test before mass production.

How should PET strap be stored?

In a dry, shaded area, off the floor, and out of direct sunlight. PET absorbs little moisture compared with PP, but sustained UV exposure degrades it, and long storage under load can set a coil memory that causes feeding problems.

Source PET Strapping Band from Pefilmpack

Weishan Litong Packing Material Co., Ltd. produces PET strapping band for importers, distributors, and industrial end users, supplied factory-direct with export packaging. Width, thickness, break strength grade, surface finish, color, coil weight, and coil core are specified per order, so strap can be matched to a specific load and to the tensioning tooling already on site rather than accepted as a catalogue grade. Coils are packed for container shipment, with labels carrying batch, width, thickness, and coil weight. OEM branding is available for distributors.

To receive a quotation, send: strap width and thickness, break strength requirement, surface finish, color, coil weight and core, joint method, packaging preference, order quantity, and destination port. Our team will confirm the specification against your load and reply with a coil specification sheet. Contact Pefilmpack, or review the PET strapping band range, the PET strapping band product page, and our guide to strapping tools and joints.

Shopping Cart