Meta description: Core diameter, roll weight and wound length decide whether a stretch film roll runs on your wrapper and what each wrapped pallet really costs. Here is how to read and verify all three.
Table of Contents
- What the Three Numbers Control
- Core Diameter: 2-Inch vs 3-Inch
- Roll Weight and Wound Length
- Roll Outside Diameter and Machine Fit
- Matching Rolls to the Wrapping Method
- Specifications to Confirm in an RFQ
- Common Purchasing Mistakes
- How to Inspect Rolls at Goods Receipt
- Frequently Asked Questions
- Source PE Stretch Film from Pefilmpack
What the Three Numbers Control
Three numbers describe a finished stretch film roll before any performance data is quoted: the inner core diameter, the roll weight, and the wound length. Gauge and width determine how the film behaves on the load. These three determine whether the roll fits the machine, how often operators change rolls, and what you pay per meter.
Buyers frequently compare rolls by weight alone. Two rolls of the same width and the same 15 kg weight can differ by several hundred meters once gauge changes, because length is weight divided by cross-section. A quote that lists only roll weight cannot be compared across suppliers. For the gauge and width side of the specification, see our guide to stretch film thickness and width for export pallets.
Core Diameter: 2-Inch vs 3-Inch
Core diameter cannot be corrected after the container arrives. If the bore does not fit the mandrel, the roll does not run, and no amount of operator skill fixes it.
76 mm (3 inch) cores
The 3-inch core is the default for machine grade rolls. The wider bore accepts heavier rolls and matches the roll carriage on most turntable and rotary arm wrappers. Machine rolls on 76 mm cores commonly run in the 10–20 kg range, so confirm carriage capacity and mandrel length rather than assuming any 3-inch roll will fit.
50 mm (2 inch) cores
2-inch cores are typical for hand rolls and light rolls on small semi-automatic wrappers, because dispensers and hand tools are built around that bore. A 50 mm core will not center on a 76 mm shaft without an adapter, and an adapter that is not properly seated causes film wander and edge damage.
Core material and wall strength
Paper cores are adequate for most export shipments but absorb moisture in humid storage, which softens the wall and lets a heavy roll deform under its own weight. Plastic cores resist moisture and repeated handling, and are the safer choice for tropical destinations and rolls that sit in a container for weeks. On automated lines, a crushed core causes tracking faults that look like film defects.
Roll Weight and Wound Length
Wound length is derived, not independent. For polyethylene film, length in meters can be estimated by dividing roll weight by the product of density, width, and thickness, with PE density typically taken as about 0.92 g/cm³. The result is an estimate because winding tension and gauge tolerance shift the real figure, but it is close enough to compare two quotes.
Illustrative example: a 15 kg roll at 500 mm width and 20 micron works out to roughly 1,600 meters, while a 2 kg hand roll at 450 mm width and the same gauge comes to roughly 240 meters. Use the formula to test whether a quoted weight is plausible for the gauge and width on offer, then ask the supplier to state wound length as a contractual figure.
Roll format also sets labor cost. A roll that runs out mid-pallet forces the operator to restart the wrap, wasting film and time. Longer rolls reduce changeovers but add weight, and weight is limited by what the carriage and operator can handle safely.
| Roll format | Core | Typical roll weight | Where it fits |
|---|---|---|---|
| Hand roll | 50 mm (2 in) | Commonly 1.5–3 kg | Manual wrapping, small dispatch areas, low pallet counts |
| Machine roll | 76 mm (3 in) | Commonly 10–20 kg | Turntable and rotary arm wrappers, semi-automatic and automatic lines |
| Light machine roll | 50 mm or 76 mm | Commonly 5–10 kg | Compact semi-automatic machines, low-volume sites, test runs |
| Mill or jumbo roll | Depends on rewinder | Set by the converter | In-house slitting and rewinding operations |
Ranges above reflect common market practice, not a fixed standard. Requirements may vary by application, market and applicable standard. For mother rolls and in-house rewinding, see the jumbo roll stretch film guide.
Roll Outside Diameter and Machine Fit
Outside diameter is the specification buyers forget, and it causes the most avoidable downtime. Two rolls of identical weight can differ in diameter because winding tension differs: a hard-wound roll is denser and smaller, a soft-wound roll is bulkier for the same meters.
The consequence is practical. A soft-wound roll may exceed the carriage guard clearance or the maximum roll diameter published for the machine, and it will rub or bind before the film is finished. Soft winding also leaves the inner layers at lower tension, so the roll can telescope in transit and the stepped end face tracks badly. Ask for maximum outside diameter and winding tension policy in writing, not only for weight.
Matching Rolls to the Wrapping Method
Roll format should follow the wrapping method, not the freight budget. Three mismatches are common, and each is expensive in a different way.
- Hand roll on an automatic line. Light rolls on 2-inch cores cannot be loaded onto a 3-inch mandrel, and an adapter still runs out too fast for line speed.
- Machine roll for manual wrapping. A 15 kg roll held by hand is a handling injury risk, and hand tension cannot exploit a machine grade film.
- Soft-wound roll on a high-speed carriage. Uneven tension produces inconsistent pre-stretch and variable containment force, which appears later as corner damage in transit.
On high-speed lines, the roll specification is part of the machine specification. Our notes on machine grade stretch film for high-speed wrapping cover the film properties that pair with tight roll tolerances. Where pre-stretch is used, roll meters and delivered meters diverge, as explained in the pre-stretched film yield guide.
Specifications to Confirm in an RFQ
- Thickness in micron or gauge, with the tolerance allowed per roll.
- Width in mm, and whether width is measured over the full web.
- Wound length in meters per roll, stated as a minimum rather than an average.
- Roll weight in kg, with the accepted range per roll.
- Core inner diameter (50 mm or 76 mm) and core material.
- Maximum outside diameter and the winding tension or hardness expectation.
- Hand grade or machine grade, with tack requirement (one-sided or two-sided).
- Packaging: rolls per carton or per pallet, pallet height, labels and shipping marks.
Where a supplier cannot state wound length, ask for weight, gauge, and width and calculate it. A figure well below the offered meters means gauge or width is being described loosely.
Common Purchasing Mistakes
- Buying on roll weight alone. Price per kilogram is not a cost metric when gauge and width are not fixed.
- Assuming core sizes are interchangeable. They are not, and adapters introduce tracking problems.
- Ignoring outside diameter. Carriage clearance and guard height are hard limits on a wrapping machine.
- Ordering hand rolls to save freight. A cheaper container load that cannot run at line speed costs more than the freight saved.
- Skipping the wound-length clause. Without a stated minimum, a gauge reduction in a later batch silently shortens every roll.
How to Inspect Rolls at Goods Receipt
Roll specification is verifiable in under an hour with a caliper, a scale, and a meter counter.
- Measure core inner diameter on three rolls per pallet with a caliper, not a tape measure.
- Weigh three rolls against the stated range; a systematic shortfall points to gauge, not scale error.
- Run the first roll through a meter counter or the machine’s film-length display and compare with the declared length.
- Measure thickness at three points across the web and record the minimum.
- Check end faces for telescoping, ovality, and edge damage, and confirm labels carry batch, gauge, width, length, and weight.
- Retain one roll per batch as a reference sample for the next delivery.
Frequently Asked Questions
Can a 3-inch core roll be used on a machine built for 2-inch cores?
Not without a different mandrel or a properly engineered adapter, because the bore is larger than the shaft and the roll will not center. Confirm the mandrel diameter before ordering and specify that bore on every purchase order.
How many meters are on a 15 kg machine roll?
It depends on gauge and width. At 500 mm width and 20 micron, the estimate is roughly 1,600 meters; a 23 micron roll of the same weight carries noticeably fewer. Ask for wound length as a stated figure rather than calculating it after delivery.
Why is this batch shorter than the last one at the same weight?
Usually a gauge change, a width change, or a different winding tension. Gauge drifting toward the lower tolerance limit saves resin for the producer and costs delivered meters for the buyer. A wound-length minimum in the contract closes that gap.
Can roll weight and core size be customized?
Yes. Width, thickness, wound length, roll weight, core size, and core material are specified per order in factory-direct supply. Custom roll weights are common where a machine has a fixed carriage capacity.
Is a heavier roll always cheaper per meter?
No. Heavier rolls cut changeover labor but raise handling risk, freight weight, and mandrel load. Compare cost per wrapped pallet, which combines delivered meters, film consumption, and downtime.
How should rolls be stored before use?
Upright on their end faces or on a roll rack, out of direct sunlight, away from heat sources, and off concrete floors in humid climates. Film stored against a hot wall or under UV can lose tack and block between layers.
Source PE Stretch Film from Pefilmpack
Weishan Litong Packing Material Co., Ltd. supplies PE stretch film factory-direct in hand grade and machine grade, blown and cast, for importers, distributors, and export packers. Width, thickness, wound length, roll weight, color, and core size are specified per order, so a roll can be built around the carriage capacity and mandrel diameter of the machine it will run on. Rolls run on 50 mm or 76 mm cores as required, with export packaging, pallet configuration, and shipping marks agreed before production. OEM branding and printed core labels are available for distributors.
To receive a quotation, send the film type and grade, width, thickness, wound length or roll weight, core diameter, tack requirement, packaging preference, order quantity, and destination port. Our team will confirm the specification against your wrapping method and reply with a roll specification sheet. Contact Pefilmpack, or review the PE stretch film range and the PE stretch film product page.