Meta description: Why machine-grade PET strap fails in automatic heads: coil format, joint type, tension settings, loop patterns and six jam causes, with cost per pallet.
An automatic strapping head is an unforgiving consumer of strap. It pulls a loop at a fixed speed, closes a joint under programmed pressure, and repeats the cycle several hundred times a shift. Strap that behaves well in a hand tool often stops the same machine within an hour, and the cause is rarely break strength: it is coil format, surface, joint compatibility or the tension curve.
This guide covers what changes when PET strapping moves from manual baling to an automatic pallet strapper: which specification items matter, how to size tension for a load rather than a bale, how to calculate cost per pallet, and where jams actually come from.
Machine Grade Is a Different Specification
Hand-grade and machine-grade PET strap can share a width and thickness and still be different products. Machine grade is defined by consistency along the coil: uniform thickness over the full length, controlled camber so the strap tracks straight through the dispenser, and stable surface friction so feed rollers grip without slipping.
Two consequences follow. A quotation that specifies only width and thickness has not specified a machine-grade strap. And the comparison between suppliers has to be made on joint efficiency and jam rate, not on dollars per kilogram, because a strap that jams twice a shift consumes labor that never appears on the invoice.
Coil Format Decides Whether the Machine Can Run It
Automatic heads are built around a coil type. Fitting the wrong format means an adapter, a new dispenser, or a machine that will not run.
| Coil format | Typical use | Feeding behaviour | Confirm before ordering |
|---|---|---|---|
| Ribbon-wound coil | Most automatic pallet and carton strappers | Unwinds flat from the outside of the coil | Inner and outer diameter and coil weight must match the dispenser drum |
| Traverse-wound coil | Some high-speed heads and accumulator systems | Pays off from the side through a controlled path | Whether the head accepts traverse winding at all |
| Coreless coil | Manual tools and simple semi-automatic heads | Collapses as it is consumed unless held under tension | Whether the dispenser has a mandrel; unsuitable for most automatic heads |
Coil length is the second variable. A longer coil reduces changeover frequency but increases the weight the dispenser carries and the inertia the brake controls. On a high-cycle line the practical limit is set by the brake, not by the operator’s willingness to lift a heavier coil.
Joint Type: Friction Weld, Seal, or Seal-Less
PET strap is joined in one of three ways on automatic equipment, and the strap has to suit the method.
- Friction weld. The head rubs the strap against itself under pressure to fuse the interface. Joint efficiency depends on surface consistency and on the strap being genuinely PET.
- Metal seal. A crimped seal closes the loop. Slower, but tolerant of surface variation and common on heavy loads.
- Seal-less. The head folds and welds the strap onto itself. Fast and clean, but sensitive to thickness tolerance at the overlap.
Ask the machine supplier which method the head uses, then ask the strap supplier whether the strap is recommended for it. A strap that welds reliably in one head can produce opening joints in another at identical settings.
Setting Tension for Pallet Loads
Pallet strapping is not baling. A bale is compressed and the strap holds the compression; a pallet load is stacked and the strap holds the stack against movement. Over-tensioning a pallet is therefore not a safety margin but a damage mechanism: cartons crush at the strap line, the board creeps, and the load arrives loose with a visible indentation.
A workable sequence for a new load is to start below the expected tension, run three pallets, and inspect for indentation and for strap movement under a firm hand push. Increase in small steps until the load is stable, then stop. Record the setting and the strap specification together, because changing either invalidates the other.
Edge protection changes the tension the carton actually sees, so a load that crushed without protectors may run fine with them at the same setting. Stretch-wrapped pallets also need less strap tension, not more, because the film adds containment.
Strap Count and Loop Pattern
The number of straps follows load height, weight and handling, not a fixed rule. Tall loads need vertical straps tying the stack to the pallet; wide loads need horizontal straps resisting racking; loads that will be double-stacked need both.
Vertical loops must pass under the pallet deck or through its openings, so the strap has to be long enough and the loop geometry has to match the pallet type. This is the most common specification error: a strap sized for a bale is too short for a pallet girth, and the head faults out mid-cycle.
Cost per Pallet: A Worked Example
Strap cost per pallet is a short calculation once loop length is known. Take a pallet 1200 by 1000 mm and 1400 mm high, with two vertical and two horizontal straps.
- Vertical loop: 2 x 1400 mm plus 2 x 1000 mm, plus 300 mm for joint and slack, about 5.1 m.
- Horizontal loop: 2 x 1200 mm plus 2 x 1000 mm, plus 300 mm, about 4.7 m.
- Total consumption: 2 x 5.1 m plus 2 x 4.7 m, about 19.2 m per pallet.
- At roughly 12.5 g per meter for 15.5 by 0.6 mm PET strap, that is about 240 g per pallet.
- At an illustrative USD 1.40 per kilogram, material cost is about USD 0.34 per pallet.
Substitute your own loop length, linear weight and landed cost. The conclusion is structural rather than numerical: at this order of magnitude, material cost is small against the cost of a jammed head or a rejected load, which is why consistency deserves more weight than a few cents per kilogram.
Six Reasons Automatic Strapping Heads Jam
- Camber outside tolerance. The strap curves as it feeds and misses the guide track. Visible by laying three meters of strap on a flat floor.
- Coil wound too loosely. The strap tightens onto itself under unwind tension and the head pulls harder than the brake can control.
- Thickness variation along the coil. Feed rollers lose grip at thin sections and the loop stalls part-way around the load.
- Incorrect loop length for the load. The head cannot complete the loop and faults out; the strap is usually fine.
- Wrong joint parameters. The head welds at settings intended for another material, producing joints that open in transit rather than jams on the line.
- Storage damage. Coils stored on their side or in humid conditions take a set, which shows up as feed problems in the first meters of every coil.
What to Specify in the RFQ
A machine-strapping enquiry that omits the machine produces a strap that fits only by accident.
- Strap width, thickness and the break strength the load requires.
- Coil format, inner diameter, outer diameter and nominal coil weight or length.
- Surface type, smooth or embossed, and any requirement the head imposes.
- Joint method used by the machine: friction weld, seal or seal-less.
- Colour, and whether printing is needed for load identification.
- Machine make and model, cycle rate, and pallet dimensions including girth.
- Order quantity in coils and containers, and whether a trial coil is required first.
Width and break strength selection is covered in our guide to PET strapping width, thickness and break strength, the joint side in the tools and joints guide, and the compressed-load case in the baling application guide.
Frequently Asked Questions
Can hand-grade PET strap be used in an automatic machine?
Sometimes, briefly. Hand-grade coils vary more in thickness and camber, which the feed mechanism cannot compensate for. The result is intermittent jams and open joints rather than immediate failure, which makes diagnosis harder. Use machine-grade strap where the head is automatic.
What width of PET strap do most pallet strappers use?
Commonly 12.7 mm to 19 mm, with 15.5 mm and 16 mm widely used on general pallet loads. Narrower strap concentrates force and can crush carton edges; wider strap spreads the load but needs a head designed for it. Confirm the head’s specified range.
How much tension should a pallet strap carry?
There is no universal figure, because it depends on carton compression strength and load geometry. Set it by test: start low, run three pallets, inspect for indentation and movement, then increase in small increments. Record the setting with the strap specification.
Does PET strap relax over time on a pallet?
PET resists creep better than PP, but it is not immune. On long ocean transits, corrugated cartons compress and the strap loses tension even though the strap itself has barely stretched. Edge protectors and a slightly higher initial tension help; so does re-checking loads after the first week of a new route.
Why do joints open in transit when they tested fine at the plant?
Usually because the joint was tested on a stationary load. Vibration and repeated flexing work a marginal weld open. Increasing weld time slightly, and pulling a sample to failure rather than inspecting it visually, gives a better indication.
Can PET strap be printed for load identification?
Yes, and it is common on loads moving through distribution centers. Printing is applied during extrusion, so it adds lead time and requires a minimum order quantity per design. Send artwork with the enquiry and confirm the minimum first.
Sourcing PET Strapping from Pefilmpack
Weishan Litong Packing Material Co., Ltd. supplies PET strapping band in smooth and embossed surfaces, with width, thickness, colour and coil format open to customization for machine or hand application. Coils can be produced to the inner diameter, outer diameter and weight your dispenser accepts, packed for direct container loading, and quoted alongside stretch film, BOPP tape and shrink film so a mixed order ships together. Tell us the machine model, pallet girth and load weight, and we will confirm which coil format and strap grade fit.
Send Your Specifications — contact Pefilmpack with strap size, coil format, machine model and destination port, or review the PET strapping band range first.