Pallet Wrapping Pattern: Overlap, Anchor Turns and Film Path

Meta description: Overlap percentage, anchor turns and banding decide whether a pallet arrives square and how much film it consumes. Here is how to specify a wrap pattern that holds without over-wrapping.

Table of Contents

Why the Pattern Matters More Than Film Gauge

Two pallets can leave the same warehouse wrapped in the same 20 micron machine film and arrive in very different condition. The variable that usually explains the gap is not the film but the pattern: how many turns sit at the base, how far each spiral overlaps the pass below it, whether the top layer is tied down, and whether the film path runs straight up the load or returns down it.

A pattern is an instruction, and like any instruction it can be written down, measured and repeated. Buyers who leave it to operator habit tend to pay twice: once for film that does not hold, and again for the damage claim. PE stretch film only performs as well as the pattern it is applied in, which is why the pattern belongs in the specification rather than in the training folder.

The Four Elements of a Wrap Pattern

Every pattern is built from four variables. Fix all four in the machine recipe or the purchase order, otherwise the pallet that leaves the line on Monday will not match the pallet that leaves on Friday.

  1. Overlap percentage — how far each revolution advances down the load relative to the film width.
  2. Anchor turns — full-width turns at the base that bond film to the pallet itself, not just to the cartons.
  3. Film path — a single spiral upward, a spiral up and back down, or discrete bands at fixed heights.
  4. Containment force — the tension the film exerts on the load at each pass, which is set on the machine separately from overlap.
Element What it controls Practical starting point
Overlap Layers of film per height band 33% for mixed cartons, 50% for unstable loads
Base anchor Whether the load can slide on the pallet 2–3 turns at deck level
Top finish Protection of the top layer, dust and rain 2 turns, or a top sheet on open loads
Film path How force is distributed over height Single spiral up; down-wrap for light loads

How Overlap Percentage Drives Film Use

Overlap is the single largest lever on both stability and film consumption, and it is the one buyers most often leave unstated. The arithmetic is simple. A 500 mm film running at 33% overlap advances 335 mm per revolution, so any given 500 mm band of load height receives roughly 1.5 layers. At 50% overlap the same band receives two full layers; at 15% it receives barely more than one.

Overlap Advance per revolution (500 mm film) Layers per band Relative film use Typical application
15% 425 mm ~1.2 1.18 Stable unitised loads, cost-driven accounts
25% 375 mm ~1.3 1.33 Uniform export cartons
33% 335 mm ~1.5 1.49 Mixed SKU pallets, retail distribution
50% 250 mm ~2.0 2.00 Tall, light, high-value or irregular loads

The final column is an index, not a price. Doubling overlap roughly doubles film consumption at the same containment force, which is why the correct question is not “how much film can we save” but “how little film still holds this load”. The answer differs by SKU, and it is worth measuring rather than assuming. Film selection itself is covered in the thickness and width guide.

Anchoring the Base and the Top

The base anchor is where most transit failures originate. Film that starts at carton level creates a load that is well wrapped but not attached to its pallet, and a unitised block that can slide as a whole is far harder to stop than loose cartons. Two to three turns at deck level, taken below the bottom carton flute, give the film something to grip; on smooth plastic pallets a mechanical tuck or heat seal is usually needed as well.

The top needs a different treatment. Two overlapping turns lock the top layer in place, and where loads are open-topped, dusty or exposed to rain, a top sheet placed under the final turns adds protection at very little cost. A pattern that stops one turn short of the top edge leaves a free flap that lifts in the airstream of an open trailer.

Choosing a Pattern by Load Type

There is no universal recipe. The pattern has to answer the specific way a load fails: sliding, bulging, leaning, settling or puncturing.

Load type Overlap Anchor Watch point
Uniform cartons, single height 25–33% 2 turns Corner crush if force is too high
Mixed cartons, stepped profile 33–50% 3 turns Void spaces collapse in transit
Drums and pails 50% 3 turns Film bridges the gaps between round surfaces
Bags and sacks 33–50% 3 turns Load settles and the wrap goes slack
Tall, light, top-heavy 50% 3 turns Leaning; consider down-wrap and a top platen
Machinery and sharp edges 33% plus corner boards 3 turns Puncture, not tension, is the failure mode

For tall or compressible loads the film path matters as much as the overlap. A second pass down the load, or banded wraps at two or three heights, resists bending far better than extra layers at the same height. Where loads are genuinely unstable, a top platen is usually more effective than more film.

What the Pattern Costs per Pallet

An illustrative calculation makes the trade-off concrete. Take a 1,200 × 1,000 mm pallet, 1,500 mm high, wrapped with 500 mm film at 20 micron and a perimeter of about 4.4 m. At 33% overlap the spiral needs about 4.5 revolutions for height, plus 3 base and 2 top turns, so roughly 9.5 revolutions and about 42 m of film, or 0.39 kg. At 50% overlap the same pallet takes about 11 revolutions and 0.45 kg.

The difference is around 60 grams of film per pallet. At a typical machine-film price that is a fraction of a cent per pallet against a damage claim, a rewrap or a customer rejection. The calculation also runs the other way: dropping from 33% to 15% saves roughly 20% of film, which is real money at volume, but only if the load still passes an incline or road-simulation test. A fuller treatment of the costing method is set out in the cost per pallet guide.

Five Pattern Mistakes That Cost Real Money

  • Wrapping cartons only. The load is sealed but not fixed to the pallet, so the whole block can slide.
  • One recipe for every SKU. Mixed and unstable loads get the same wrap as uniform cases, and fail on the road.
  • Counting turns instead of force. Ten loose turns are not equivalent to six turns at the right containment force.
  • Over-wrapping to hide a film problem. Thin or inconsistently pre-stretched film is compensated with extra layers, which costs more than the right film would.
  • Ignoring the top edge. No tie-down and no top sheet, so the top layer lifts and the wrap unravels from above.

Writing the Pattern into the Order

A pattern only holds if it survives staff changes and machine resets. The practical way to lock it in is a one-page recipe sheet per load family, with overlap, anchor turns, top finish, film path and containment force, plus a photograph of a finished pallet that operators can compare against. Ask the machine supplier to store the recipe in the controller rather than leaving it to manual entry.

For film supply, state gauge, width, core diameter and pre-stretch behaviour, and ask the supplier to recommend a pattern for your actual load list rather than a generic one. A short trial with two or three overlap settings, checked against a real shipment, settles the question faster than any specification sheet. Pattern and pre-stretch settings should be reviewed together, since both change film consumption.

Frequently Asked Questions

What overlap percentage should a pallet wrap use?

Most export operations run 25–33% for uniform cartons and 50% for irregular, tall or high-value loads. Below 20% only very stable unitised loads hold reliably.

Must the film touch the pallet deck?

Yes for any load that could slide. Two to three deck-level turns are the cheapest stability measure available, and smooth plastic pallets may need a seal as well.

How many turns should go over the top?

Two overlapping turns is the common minimum. Add a top sheet when the load is open-topped or exposed to rain and dust.

Can film use be cut without losing stability?

Often, by increasing pre-stretch and containment force while keeping overlap adequate. Reducing overlap alone usually moves the failure rather than removing it.

Does the pattern matter for hand wrapping?

Yes, and more so, because hand tension varies. Fewer, tighter turns with a proper base anchor beat many loose turns.

How can containment force be checked without instruments?

A simple pull test on the load corners, plus an incline or short road test, gives a usable comparison between two patterns.

Source Stretch Film from Pefilmpack

Weishan Litong Packing Material Co., Ltd. produces PE stretch film for export pallet wrapping in cast and blown grades, with gauge, width, core diameter, roll weight and pre-stretch performance made to order. Machine film, hand film and colored film are produced on the same lines, so a mixed order can be consolidated into one container.

Send your pallet dimensions, load weights and current film specification and we will recommend a pattern and a matching film rather than a generic quote. Samples for a wrap trial are available before volume commitment. Contact our export team to start.

Shopping Cart