Meta description: Bricks, blocks, coils and machined profiles defeat standard 17 micron film. Here is how puncture energy, tear strength, gauge and edge protection decide whether a heavy pallet arrives intact.
Table of Contents
- Why Standard Film Fails on Heavy Loads
- The Three Tests That Predict Failure
- Blown vs Cast Film for Tougher Loads
- Gauge and Pre-Stretch by Load Type
- Edge Protection That Earns Its Cost
- Machine Settings for Aggressive Loads
- Film Spend vs Damage Cost
- Common Buying Mistakes
- Running a Fair Film Trial
- Frequently Asked Questions
- Source Heavy-Duty Stretch Film from Pefilmpack
Why Standard Film Fails on Heavy Loads
A pallet of concrete blocks and a pallet of shrink-wrapped cartons are not the same packaging problem, but they are frequently wrapped with the same film. The standard 17 micron machine film that performs well on a uniform carton load has almost no margin against a sharp arris, a protruding strap buckle or a single loose brick. It does not fail gradually: a pinhole becomes a tear in one handling cycle, and the tear runs around the pallet because the film is under tension in two directions.
Three load characteristics drive the requirement. Sharp edges concentrate force on a few square millimetres of film. High mass means high inertia, so any acceleration during transport loads the film in shear rather than tension. And irregular geometry, such as hollow blocks, leaves spans of unsupported film that vibrate against the product until they abrade through.
The consequence is not only film cost. A failed wrap means a collapsed pallet, a damaged consignment, a rejected container and a claim that dwarfs the film budget.
The Three Tests That Predict Failure
Film suppliers quote tensile strength and elongation because both are easy to measure, but neither predicts performance on a sharp edge. Three other tests do, and each should appear in a specification with a value, not an adjective.
- Dart drop impact, ASTM D1709. A weighted dart is dropped onto clamped film and the energy at 50% failure is reported in grams. It measures resistance to a sudden point load, which is what a brick corner applies.
- Elmendorf tear, ASTM D1922. Reports the force required to propagate an existing tear in machine and transverse direction. Once a pinhole exists, this number decides whether it stays a pinhole.
- Probe puncture, ASTM D5748. Drives a probe into clamped film and reports the energy or peak force to rupture, the closest laboratory analogue to a protruding edge and the most useful figure for heavy loads.
Ask for all three in machine and transverse direction, on the gauge you intend to buy. A film with high tensile strength and low tear resistance is a film that holds a load until it does not. Our guide to incoming inspection of stretch film explains how to check these values on arrival rather than trusting the datasheet alone.
Blown vs Cast Film for Tougher Loads
For sharp and heavy loads, blown film is usually the better starting point. The bubble process orients the polymer in both machine and transverse direction, which produces a more balanced tear profile and, in practice, a tougher film at the same gauge. Cast film cools on a chill roll, giving excellent thickness uniformity and clarity and higher output, but its tear resistance is typically more directional.
The trade-off is real: blown film costs more per kilogram, is less clear, and is harder to source in very thin gauges. Our comparison of blown and cast PE stretch film sets out the full matrix; the short version for heavy industry is that if the load has edges, protrusions or mass above roughly 800 kg, specify blown, or specify a cast film whose puncture data proves it can cope.
Resin choice matters as much as process: a substantial metallocene LLDPE fraction delivers higher puncture and tear than a conventional LDPE-rich blend at the same gauge, which is why two films of identical thickness can differ twofold on dart impact.
Gauge and Pre-Stretch by Load Type
Gauge is the most negotiated and least informative variable in film purchasing. What matters is the gauge left on the pallet after pre-stretch, because a 23 micron film stretched 300% delivers roughly 5.7 micron of effective thickness at the load. The table gives typical starting points; treat them as the basis for a trial, not a substitute for one.
| Load type | Typical gauge | Pre-stretch | Notes |
|---|---|---|---|
| Uniform cartons, under 500 kg | 17-20 micron | 250-300% | Standard machine film |
| Bagged goods, 500-1000 kg | 20-23 micron | 200-250% | Moderate puncture demand |
| Bricks, blocks, pavers | 23-25 micron blown | 150-200% | Corner boards strongly advised |
| Coils, castings, machined parts | 25-30 micron blown | 120-180% | Edge protection mandatory |
| Profiles and extrusions | 23-25 micron blown | 150-200% | Roping at top and bottom |
Reducing pre-stretch is counter-intuitive for buyers trained to maximise film yield, but it is the right move on aggressive loads. Lower pre-stretch leaves more film on the edge, where damage starts, and reduces the tension that drives tear propagation. The yield loss is a few percent; the avoided damage is not.
Edge Protection That Earns Its Cost
No film, at any gauge, survives a sharp arris under transport vibration indefinitely. Film is the containment layer; the edge protector stops that layer being cut. Three options cover most cases:
- Corner boards on all four vertical edges, in 3 mm or 5 mm thickness depending on load mass. They spread film tension over a wide radius and add stacking strength.
- Edge protectors or U-profile board along the top and bottom rims, where the film turns through 90° under maximum local stress.
- Roping, in which the film is gathered into a cable for several revolutions at the top and bottom third, adds horizontal containment without pressing film against the sharpest part of the load.
Corner boards cost a few cents per pallet, a rounding error against one damaged engineered part, and they often allow a lighter gauge that pays for the board twice over.
Machine Settings for Aggressive Loads
A heavy-load film on a machine set up for cartons will still fail, because the machine controls how much tension reaches the edge. Four settings deserve attention on an automatic stretch wrapping machine handling sharp loads:
- Pre-stretch ratio, lowered to the range above so the film arrives at the load thicker.
- Force to load, reduced at the top and bottom revolutions where the film turns the sharpest corner.
- Carriage speed, slowed on the first revolution so the film is laid down rather than thrown against an edge.
- Overlap, increased to 50% or more on irregular loads so a torn band has a neighbour to rely on.
Settings should be recorded per product family and locked, not left to operators. One well-set recipe for bricks prevents the drift towards higher tension that quietly raises damage rates over months.
Film Spend vs Damage Cost
Heavy-duty film usually costs 15-25% more per kilogram and may run at lower pre-stretch, so film cost per pallet can rise 20-30%. That premium must be compared with the damage it prevents, using your own numbers:
Annual saving = (damage rate before – damage rate after) × pallets per year × cost per damaged pallet
As an illustration only, a plant shipping 1,000 pallets a month with a 1.5% damage rate loses 15 pallets a month. If a damaged pallet costs the value of the goods plus handling and a credit note, the annual figure easily exceeds the whole film premium. Buyers who have never measured their damage rate cannot make this comparison; the first useful step is often a two-week count. Our cost-per-pallet calculation shows how to build the film side of the equation.
Common Buying Mistakes
- Solving every problem with gauge. Moving from 17 to 25 micron without touching edge protection raises cost and leaves the failure mode intact.
- Buying on price per kilogram. Price per wrapped pallet, at the pre-stretch you will actually run, is the only comparable figure.
- Accepting a datasheet without test standards. “High puncture resistance” means nothing without a dart value and a method.
- Trialling on a perfect pallet. A trial on the neatest pallet in the plant predicts nothing; use a worst-case load.
- Ignoring cast vs blown. Two films at 23 micron can differ by a factor of two in puncture energy.
- Forgetting the machine. The best film in the catalogue fails if force-to-load is still set for cartons.
Running a Fair Film Trial
A meaningful trial needs the worst pallet you actually ship, the production settings, and a defined route. Wrap ten pallets with each film, record the settings, ship them on the same lane and inspect on arrival. Photograph the top and bottom corners before dispatch and after unloading; that is where failure shows first.
Ask for a roll long enough to finish the trial plus the lot’s test data, so the result can be tied to a specification and repeated on the next order.
Frequently Asked Questions
What gauge should I use for bricks and blocks?
23-25 micron blown film is a common starting point, applied at 150-200% pre-stretch with corner boards on all four edges.
Is blown film always better for sharp loads?
Usually, because its balanced orientation gives higher tear resistance. A cast film with strong puncture data can match it, so compare numbers rather than process names.
Why does my film tear at the top corner only?
The film turns through a sharp radius there under maximum tension. Lower the force-to-load on the top revolutions and add an edge protector.
Does higher pre-stretch save money on heavy loads?
Not usually. It thins the film exactly where the load is most aggressive, and one failed pallet erases the saving on hundreds of good ones.
Are corner boards worth the extra cost?
On loads above roughly 800 kg or with any sharp arris, yes. They often allow a lighter gauge, which offsets most of the board cost.
How do I compare two film quotations?
Convert both to cost per wrapped pallet at your real pre-stretch, then compare dart, tear and puncture data at the specified gauge.
Source Heavy-Duty Stretch Film from Pefilmpack
Weishan Litong Packing produces PE stretch film in blown and cast constructions from 12 to 30 micron, in hand and machine grades, with width, length, core size and colour made to order. Heavy-duty grades use a high metallocene content for puncture and tear, and every lot ships with dart, tear and tensile data so the specification can be verified on arrival.
Because the same factory supplies BOPP packing tape and PET strapping, we can quote a complete containment package and advise where a lighter film plus corner boards beats a heavier film alone. Send your load type, pallet weight, dimensions and monthly volume through the contact page for a specification proposal and a trial roll.