Meta description: A practical guide to silage face management: cutting tools, feed-out rates, face density, reheating checks and the bunker film specs that keep faces tight and losses low.
Most of the money invested in growing, chopping and hauling forage is either protected or lost at the silage face. A bunker can be filled correctly, packed to density and sealed with quality film, and still give up several percent of its dry matter if the face is opened carelessly and fed out too slowly. Face management is the daily, operating-side half of silage quality, and it is where buyers of bunker covers and silage film can add the most visible value for their farm customers.
Why the Face Is the Most Expensive Square Meter in the Bunker
When the cover comes off, oxygen returns and aerobic organisms resume work. Yeasts and molds consume the lactic acid and sugars that fermentation preserved, pH climbs, and heating follows. Where feed-out is slow or the face is ragged and porous, dry matter losses of 3 to 10 percent at the face are routine. Worse, reheated silage is unpalatable, so intake drops and the ration underperforms even before the tonnage disappears.
The face is also the only surface of the bunker that is disturbed every single day. Every loader pass, every sloppy cut and every loosely trimmed shoulder multiplies the area exposed to air. Unlike a fill-season mistake, which is made once, a face mistake repeats daily for months.
What a Good Face Looks Like
The target is simple to state: a vertical, smooth, dense face that sheds as little loose material as possible. Forage packed above roughly 700 kg per cubic meter resists air penetration far better than a lofted face, and a cleanly cut surface keeps the oxygen-exposed zone to a few centimeters rather than a meter or more.
- A ragged or stepped face with chunks pulled out by loader teeth, leaving fissures that let air travel deep.
- A sloped face built up over weeks of bottom-up scraping, which exposes many times more surface than a vertical wall.
- Visible heating or a sweet, tobacco-like smell within hours of cutting, a sign the aerobic zone extends behind the face.
- Loose, unpacked material raining down the face each time the loader works.
Keeping the Face Vertical
In drive-over piles and horizontal silos, the rule is to remove silage across the entire face and keep the cutting plane vertical. Face width should be calculated backward from herd consumption so the face advances at the required rate, then fixed with a side wall or a marked line. Widening the face “to make the loader’s job easier” is one of the most expensive habits in bunk silage.
On drive-over piles, maintain the face by stepping it straight back, never letting a ramp build up. A ramp doubles or triples the exposed area, invites rain wetting, and makes a consistent feed-out rate almost impossible to hold.
Cutting Tools: Defacer, Block Cutter, Shaver and Bucket
The tool chosen at the face determines face quality more than any other single decision, including film specification. Each option trades speed against surface disturbance.
| Tool | How it works | Best suited to | Watch-outs |
|---|---|---|---|
| Silage defacer | Vertical cutting frame or rotating head skimmed down the face | Slot silos with daily removal | Needs loader reach and power; keeps the face truly vertical |
| Block cutter | Cuts clean blocks for controlled feed-out | Small to mid-size operations, precision feeding | Slower; blade condition affects surface quality |
| Rotary face shaver | Shaves thin layers across the full width | Large faces and high feed-out rates | High power demand; stones damage teeth |
| Loader bucket | Digs and lifts directly | Emergencies and loose piles only | Rips and loosens the face; the highest-shrink option |
A bucket driven into a packed face opens fissures that air exploits for a meter or more behind the cutting line, while a sheared face confines the aerobic zone to a shallow layer. Operations that cannot justify a defacer should at minimum score the face vertically before lifting, and never undercut the bottom.
Feed-Out Rate: Match the Face to the Herd
The face must advance fast enough to outrun aerobic deterioration. As a working rule, remove at least 15 to 20 cm per day across the full width in cool conditions, and at least 30 cm per day in summer heat, when yeast and mold activity roughly doubles with every 10 degrees Celsius. If the herd cannot consume that much, the face is too wide and should be narrowed with a divider or a second, smaller bunker.
A quick worked example: a dairy herd eating 5 tonnes of silage per day from a bunker holding 1,500 tonnes will empty it in 300 days, far slower than summer feed-out rules allow. Splitting the storage into two faces of 750 tonnes each, fed on alternate schedules, or sealing a smaller portion separately, brings the advance rate back into range.
Reheating: The Early Warning You Can Measure
Heating is the cheapest diagnostic in face management. Two to four hours after cutting, probe the temperature 15 to 20 centimeters behind the face. A rise of more than about 8 to 10 degrees Celsius over ambient indicates oxygen is penetrating beyond the cutting plane, pointing either to low density, a ragged face, or a slow advance rate. Catching this trend early, before visible mold, is far cheaper than discarding darkened silage later.
Where the Cover Film and the Face Meet
Face losses are not only a cutting problem; they begin at the seal. A cover that transmits oxygen readily feeds the aerobic zone from above even while the face is being managed correctly. Standard polyethylene sheet is a modest barrier; oxygen-barrier films built on multi-layer structures with EVOH cores cut oxygen transmission by an order of magnitude, which is why they dominate high-value forage programs.
The same logic applies at the perimeter and shoulder, where the face meets the seal every day. Weighting and edge sealing must be restored after each cutting session, or the daily opening becomes a permanent oxygen leak. For film selection details, thickness, layer counts and UV life, see the bunker cover guide and the thickness, layers and UV guide.
Common Face Management Mistakes
- Scraping from the bottom up, which builds a sloped face and multiplies exposed surface area.
- Setting face width without calculating the daily advance the herd can actually support.
- Pulling chunks out with the loader bucket and leaving fissures behind the face.
- Cutting only part of the width today, letting the remainder sit exposed until tomorrow.
- Waiting for visible mold instead of probing for reheating as an early warning.
- Re-opening the bunker without restoring shoulder weighting and perimeter tape, so the cut line leaks continuously.
Bunker Film Specs That Support a Clean Face
Film cannot rescue a bad face, but the right specification removes one more source of oxygen at the critical zone. When requesting quotes, specify the following rather than price per roll alone:
- Structure: coextruded multi-layer sheet, with an EVOH barrier layer where forage value justifies it.
- Thickness: roughly 150 to 200 microns for standard white-over-black bunker sheet; thinner only with proven barrier performance.
- Color scheme: white outer surface to reflect heat, black inner surface to block light under the cover.
- UV stabilization matched to the real storage duration, stated in months rather than vague “UV treated” claims.
- Width and roll length sized to overhang the walls and close the perimeter without mid-slope joints.
Farms running grass and legume silages in bags or wrapped bales alongside bunkers should align these specs with the practices in the bale wrapping and sealing guide, since the aerobic logic is identical.
What Poor Face Management Costs
The arithmetic is uncomfortable but useful. Consider a 2,000-tonne bunker. A well-run face with adequate density, vertical cutting and fast feed-out might lose around 1 percent of dry matter at the face; a ragged, slowly advancing face can lose 4 percent or more. At a forage value of 45 dollars per tonne, the extra 3 percent equals 60 tonnes, or about 2,700 dollars per season, before accounting for lower intake on reheated feed. Against that, a defacer and a barrier-grade cover pay for themselves quickly.
FAQ
How far should the silage face advance each day?
At least 15 to 20 cm per day in cool weather and 30 cm or more in summer, across the entire face width. If the herd cannot support that rate, narrow the face.
Is a loader bucket ever acceptable at the face?
Only in emergencies or on loose, unpacked piles. Buckets rip fissures that let air travel deep; use a defacer or block cutter for daily feed-out.
Can better film fix a poorly managed face?
No. Film limits oxygen ingress through the cover, but a ragged, low-density or slowly advancing face will lose dry matter regardless of film grade.
What packing density should we target?
Above roughly 700 kg per cubic meter of fresh forage. Higher density slows air penetration into the face and shrinks the aerobic zone.
How do we check for reheating?
Probe 15 to 20 cm behind the face two to four hours after cutting. A rise of more than 8 to 10 degrees Celsius over ambient signals excess oxygen penetration.
Does oxygen-barrier film replace good face practice?
No. It reduces ingress through the cover and perimeter, but it works only alongside a tight, vertical, rapidly advancing face.
Work With a Factory That Understands the Whole Silage Chain
Weishan Litong Packing Material Co., Ltd. manufactures silage film and bunker covers for export markets, with coextruded structures, UV packages matched to storage duration, and widths and roll lengths customized to your bunker dimensions. Request samples and a specification sheet through our silage film product page or the silage film category, or contact our export team directly via the contact page for a quotation tailored to your face width and storage program.